Каталоги

Engine Version: for engines with dual-mass flywheel ;
Number of splines on input shaft: 28 ;
ArticleState: Normal ;
Technical Information: self adjust clutch ;
Technical Information: 3 in 1

Number of Teeth: 28 ;
Diameter [mm]: 228 mm ;
Weight [kg]: 6,05 kg ;
Multi-piece: Three-piece ;
ArticleState: Normal

Number of Teeth: 28 ;
Outer diameter [mm]: 230 mm ;
Engine Version: for engines with dual-mass flywheel ;
Supplementary Article/Info 2: with bearing(s) ;
Multi-piece: Four-piece ;
ArticleState: Normal

Diameter [mm]: 230 mm ;
Supplementary Article/Info 2: with clutch plate ;
Supplementary Article/Info 2: with releaser ;
Supplementary Article/Supplementary Info: with clutch pressure plate ;
Supplementary Article/Info 2: with screw set ;
Adjustment: with automatic adjustment ;
Supplementary Article/Info 2: Requires special tools for mounting ;
Engine Version: for engines with dual-mass flywheel ;
ArticleState: in Preparation

Outer diameter [mm]: 230 mm ;
Number of Teeth: 28 ;
Weight [kg]: 5,022 kg ;
Observe service information: ;
ArticleState: Normal ;
General Information: Die von uns gelieferten Produkte sind ausschließlich dem bestimmungsgemäßen Gebrauch zuzuführen. Der Einbau darf nur durch geschultes Fachpersonal erfolgen. Produkte werden in der Regel ohne Montageanleitung geliefert.

Engine Version: for engines with dual-mass flywheel ;
Supplementary Article/Info 2: with flywheel ;
Supplementary Article/Info 2: with screw set ;
Adjustment: with automatic adjustment ;
Supplementary Article/Info 2: Requires special tools for mounting ;
Max. Clearance Angle [Degree]: 18 º ;
Number of teeth (finding the max. clearance angle): 7 ;
Max. Sideplay [mm]: 2,9 mm ;
Supplementary Article/Info 2: Dual-mass flywheel with friction control plate ;
Number of mounting bores: 6 ;
Supplementary Article/Supplementary Info: without pilot bearing ;
ArticleState: Normal

Diameter [mm]: 230 mm ;
Supplementary Article/Supplementary Info: with clutch pressure plate ;
Supplementary Article/Info 2: with clutch plate ;
Supplementary Article/Info 2: with releaser ;
Supplementary Article/Info 2: with clutch slave cylinder ;
Adjustment: with automatic adjustment ;
Supplementary Article/Info 2: Requires special tools for mounting ;
Engine Version: for engines with dual-mass flywheel ;
Supplementary Article/Info 2: Check and replace dual-mass flywheel if necessary. ;
ArticleState: Normal

Number of Teeth: 28 ;
Diameter [mm]: 228 mm ;
Supplementary Article/Info 2: with bearing(s) ;
Supplementary Article/Info 2: Self-adjusting ;
Multi-piece: Three-piece ;
Plate diameter [mm]: 228 mm ;
ArticleState: Normal

Number of Teeth: 28 ;
Diameter [mm]: 228 mm ;
Diameter 2 [mm]: 228 mm ;
Clutch: Conversion from dual-mass flywheel to single-mass flywheel ;
Clutch Equipment: 4 Piece ;
Supplementary Article/Info 2: with guide sleeve ;
ArticleState: Normal ;
Technical Information: Installationssatz schließt einzelnes Massenschwungrad mit ein, um Doppelmassenschwungrad zu ersetzen

Diameter [mm]: 230 mm ;
Adjustment: with automatic adjustment ;
ArticleState: in Preparation

Diameter [mm]: 228 mm ;
Number of Teeth: 28 ;
Supplementary Article/Info 2: with bearing(s) ;
ArticleState: Normal ;
Technical Information: nur als Kupplungskit lieferbar

Number of Teeth: 28 ;
Diameter [mm]: 228 mm ;
Multi-piece: Four-piece ;
Plate diameter [mm]: 228 mm ;
ArticleState: Normal

Diameter [mm]: 228 mm ;
Number of Teeth: 28 ;
Mounting Type: not pre-mounted ;
ArticleState: Normal ;
Technical Information: Beinhaltet ZMS, Kupplungsdruckplatte, Kupplungsscheibe und Ausrücker ;
Technical Information: enthält Druckplatten- und Schwungradbefestigungsschrauben

Diameter [mm]: 228 mm ;
Hub Profile: 20,3x22,1-28N ;
Number of Teeth: 28 ;
ArticleState: Normal ;
Technical Information: Nur als Satz lieferbar ;
Technical Information: enthält Druckplattenbefestigungsschrauben

for OE number: 3000 951 120 ;
Diameter [mm]: 230 mm ;
ArticleState: in Preparation

New Part: ;
Supplementary Article/Supplementary Info: with clutch pressure plate ;
Diameter 1 [mm]: 228 mm ;
Supplementary Article/Info 2: with clutch plate ;
Diameter 2 [mm]: 228 mm ;
Number of Teeth: 28 ;
Supplementary Article/Info 2: without releaser ;
Weight [kg]: 5,05 kg ;
ArticleState: No longer supplied by manufacturer ;
Technical Information: 2-Komponenten-Kit (Druckplatte & Scheibe)